Wire Strain Relief for Printrbot Simple Metal Heat Bed Modification 3d models

Ensure that the hot end thermocouple amplifier circuit board's wire has proper strain relief.

I designed this adapter to secure the wire to bed arms, preventing unwanted movement. Print it once or twice, depending on your needs - it's a straightforward print. I used my wire with a 5mm diameter; feel free to adjust the design to fit your...

... to perform upgrades, maintenance, and other tasks. ... Based on it, I transformed the original design so that the strain relief can be slid up and removed from the bracket without taking out the entire bracket or the zip ties holding the wire bundle.

The Essential Tool for Precise Printrbot Simple Metal Calibration: A 17mm Wrench.

... remixed this to fit on my Tronxy XY-2 pro heated bed. ...It is a simple cable strain relief. If you're going to use this I would suggest lengthening your heated bed power cables just to give you that extra slack. ...You will also need a small zip-tie.

This is an innovative heatbed connector strain relief designed to securely fasten onto the metal plate located beneath the bed, specifically underneath the mattress springs. ...Its primary function is to alleviate stress on the heated bed while...

This mount is specifically designed for the Logitech C270 webcam and attaches seamlessly to a Printrbot Simple Metal bed mount. The mount cleverly uses the C270's hinge pin, eliminating the need for any additional hardware. The design provides both...

I remixed http://www.thingiverse.com/thing:39778 to hold be usable for the printrbot metal simple.

Part Number: 2X-TRNXY-X5SA Description: Part replacement for TRONXY X5SA. ... Compatibility: Specifically designed for use on TRONXY X5SA models. ... Product Type: Replacement part.

Engineers Created a Heated Bed Strain Relief That Sits on 18mm Silicone Spacers Around the ADIMLab Gantry. The Goal Was to Keep the Part from Interfering with the Height of the Spacers. Additionally, A Split Version was Designed That Clamps Together...

... model: https://www.aliexpress.com/item/220x220x0-5mm-PEI-Sheet-Polyetherimide-Build-Surface-3D-Printer/32834236853.html. ...Note that for a 220x220mm PEI sheet, you will need to trim one side down to 168mm to fit the Printrbot Simple Metal print bed.

This is a straightforward strain relief for heated bed wiring on Prusa i3 style printers. To mount this particular design, you'll need to drill two 3mm holes through the aluminum bed, so proceed only if you're willing to modify your print bed. I...

This is based on my previous creation of an LED Light Strip mount for your Printrbot Simple Metal. It holds two strips of LED Light Strips and rests above the Extruder plate with secure hangovers in the back. I installed it according to the...

I'm using Wire Relief for heated bed and chamber sensor wires with my xBot Printer design. The wire relief is secured to the Z-Gantry plate by two m3 12mm screws. It's positioned so that the wires are tucked under the corner of the bed, preventing...

The wires are held at a slight angle to accommodate for enclosures that may restrict the height of your setup and would otherwise kink them. Underneath of the attachment, there is a small slot to allow the fan wire to pass through to the other side...

This is a minimalist mount specifically designed for low-profile 50mm fans on Printrbot Simple Metal 2014 to keep extruder motor temperatures under control. Screw holes are carefully crafted to accommodate countersunk self-tapping screws - the type...

This clamp securely attaches itself around the new Printrbot Simple Metal bed, which features the 10" x axis upgrade. The modified camera arm slides smoothly into its custom hole. Depending on your printer's specifications, you may need to adjust the...

Then, use a zip tie to secure the power and thermistor wires coming off the heated bed, relieving strain and preventing them from cracking due to Y-axis movement. Inspired by Thing #1940087, this design was completely redesigned in Fusion 360 from...

Based on the LED Holder for Printrbot Simple Metal by Sibanamush, I created a simplified design that utilizes LED strip lighting instead of individual LEDs. The entire part is one continuous piece and features a skirt to block stray light and zip-tie...

Print Settings Printer Brand: Printrbot Printer: Printrbot Simple Metal Rafts: No rafts needed for this print Supports: No supports required Resolution: A fine resolution of 0.2mm is recommended Infill: A moderate infill setting of 15% provides a...

Normally, these cables are soldered to the bed, and over time, the up and down movement causes the solder to weaken - providing strain relief in this manner allows the cable to move freely, but not at the bed end.\r\n\r\nIt's a basic print, sitting...

It attaches to this Printrbot Simple Metal bed mount. http://www.thingiverse.com/thing:442063 It uses the C270's hinge pin so no need for any extra hardware. Allows for horizontal and vertical swivel to get your camera alignment just right. December...

The Cable Strain Relief is designed to be placed over the Connector and Zip-tied in-place. I recommend using ABS or you'll have serious issues with warping due to the radiant heat from the bed.I've also included my STEP file if folk want to...

This is a wire guide or strain relief that bolts on to the top of the e3d Hemera in conjunction with the Ender 3 adapter plates from their guide. ... You can always shorten the length of the channel if you have other needs.

This adapter/support is precision-designed for a seamless fit on the Printrbot Simple Metal printer, perfecting its integration with the Dyze Design DyzEND. dyzedesign.com - The precision achieved here is nothing short of incredible! I immediately...

I've created this custom corner mount for my trusty GoPro camera, specifically designed to sit securely on the Printrbot's sturdy metal bed. ...To make it work seamlessly, I cleverly rearranged the original components so they now nestle snugly on the...

I lost one cable on my CR10 S5 due to wear and tear, prompting me to create a strain relief bracket for my new heated bed cable, but the official bracket no longer fits since Creality began installing an aluminum frame under the bed. I decided to...

Based on the LED Holder for Printrbot Simple Metal by Sibanamush.I simplified his design to use LED strip lighting instead of individual LEDs. The entire part is one piece and includes a skirt for blocking stray light and zip-tie holes to prevent the...

You'll need to secure these feet firmly onto a solid surface to prevent your Printrbot Simple Metal from shifting or moving while it's printing.

These parts are designed to provide essential strain-relief for the wires as they exit from the bed and where they enter the printer's case. There are two passages on the top sized for 2mm cable-ties that securely fasten the wires to the mount. One...